This highly modified Piper PA-18 Super Cub was built in Talkeetna Alaska. The paint scheme, designed by Curt Holler, was intended to pay tribute to the beauty of the surrounding area, and the spirit of Talkeetna. Check out the spec sheet online at https://abovealaska.com/supercub-raffle/ for all of the amazing modifications! Alaska Airmen Association 2016 Super […]
Posts tagged "2016 Super Cub Raffle Plane"
Time Lapse 23: Final Assembly of the 2016 Alaska Airmen Super Cub Raffle Plane

Wings on! The final assembly and finishing touches on the 2016 Alaska Airmen Super Cub raffle plane. Alaska Airmen Association 2016 Super Cub Rebuild
Time Lapse 22: Painting the Fuselage of the 2016 Alaska Airmen Super Cub Raffle Plane

It’s the time lapse that everyone has been waiting for! The fuselage of the 2016 Alaska Airmen Super Cub raffle plane, is painted! A lot of time, patience, and attention to detail went in to producing a superior paint job! Alaska Airmen Association 2016 Super Cub Rebuild
Time Lapse 21: Installing Poly Fiber on The 2016 Alaska Airmen Super Cub Fuselage

Installing Poly Fiber fabric on the 2016 Alaska Airmen Super Cub raffle plane. As simple as it may seem, poly fiber fabric is 100% polyester. Total fabric and coating weight is about 60 pounds. There are just six basic steps: Glue on the fabric with our Poly-Tak fabric cement; tighten it with the heat of […]
Time Lapse 20: Painting the Raven Wings of the Alaska Airmen 2016 Super Cub Raffle Plane

A silver UV protection coat is sprayed then requires 5 days to gas off. Aerothane Polar Grey is sprayed over the entire surface of the wings, tail feathers, flaps and ailerons, and left to cure for 24 hours. The stripes are taped off and covered in paper layers. Ag Cat Grey is sprayed and left […]
Time Lapse 19: Installing Poly Fiber Interior on the Alaska Airmen 2016 Super Cub Raffle Plane

Keeping in mind our goal of having a lightweight super cub, we decided to install a Poly Fiber interior. Not many people have seen Poly Fiber interiors. It takes a little bit of extra time to work in the intricacies of this installation, so we have made this video a bit longer than the […]
Time Lapse 18: Custom Built Carbon Fiber Floors For the Alaska Airmen 2016 Super Cub

What is the best way to increase your payload? Carbon Fiber! We have several carbon fiber mods that we are equipping the Alaska Airmen 2016 Super Cub raffle plane with! A big ‘Thank You!’ to Carbon Concepts http://www.carbonconceptsak.com/ for their sponsorship and providing the bulk carbon fiber layups! Alaska Airmen Association 2016 Super Cub Rebuild
Time Lapse 17: Painting Silver On The Control Surfaces Of The Alaska Airmen 2016 Super Cub

What does the painting process entail? There are six basic steps: Glue on the fabric with Poly-Tak fabric cement; tighten it with the heat of a calibrated iron. Brush on a coat of Poly-Brush fabric sealer. Riblace, then apply gussets and finishing tapes with more Poly-Brush. Spray on two more coats of Poly-Brush. Spray on […]
Time Lapse 16: Fabricating the Instrument Panel of the Alaska Airmen 2016 Super Cub

What does it take to fabricate a customized instrument panel? Watch this week’s time lapse to find out! Instruments and avionics for the Alaska Airmen 2016 Super Cub raffle plane are being donated by the following sponsors: Alaska Airmen Association 2016 Super Cub Rebuild
Time Lapse 15: Poly-Brush, Rib Stitching and Finishing Tapes

In this video of the Alaska Airmen 2016 Super Cub Raffle Plane: 1. Applying Poly-Brush, which acts as a sealer for the Poly-Fiber materials. 2. Applying reinforcing tapes and rib-stitching with Poly Fiber thread. This secures the Poly Fiber fabric to the wing. 3. Applying ‘finishing tapes’ to give the wing a tidy appearance, and […]